DN to NPS Pipe Size Conversion
Convert between DN (Diameter Nominal) and NPS (Nominal Pipe Size) and look up the pipe outside diameter in millimetres and inches. Pick a size on either side — the other follows.
Pick either side — the other follows. Outside diameters are the ASME series.
8 of 14 rows were checked against a source; the other 6 still need a second source check. Rows marked “to confirm” show the best available values — verify them before ordering.
| DN | NPS | OD (mm) | OD (in) | Status |
|---|---|---|---|---|
| DN15 | NPS 1/2 | 21.3 | 0.8386 | Checked |
| DN20 | NPS 3/4 | 26.7 | 1.051 | Checked |
| DN25 | NPS 1 | 33.4 | 1.315 | Checked |
| DN32 | NPS 1-1/4 | 42.2 | 1.661 | to confirm |
| DN40 | NPS 1-1/2 | 48.3 | 1.902 | Checked |
| DN50 | NPS 2 | 60.3 | 2.374 | Checked |
| DN65 | NPS 2-1/2 | 73 | 2.874 | to confirm |
| DN80 | NPS 3 | 88.9 | 3.5 | Checked |
| DN100 | NPS 4 | 114.3 | 4.5 | Checked |
| DN125 | NPS 5 | 141.3 | 5.563 | to confirm |
| DN150 | NPS 6 | 168.3 | 6.626 | Checked |
| DN200 | NPS 8 | 219.1 | 8.626 | to confirm |
| DN250 | NPS 10 | 273 | 10.75 | to confirm |
| DN300 | NPS 12 | 323.9 | 12.75 | to confirm |
Formula
There is no formula for DN to NPS. The correspondence is a nominal-size table fixed by ISO 6708 and ASME B36.10 — a lookup, not a calculation. The only arithmetic on this page is the unit conversion for the outside diameter:
| Symbol | Meaning | Unit |
|---|---|---|
| OD (mm) | Pipe outside diameter | mm |
| OD (in) | Pipe outside diameter | in |
DN and NPS are both nominal designations: neither one is a measured diameter. DN100 pipe does not measure 100 mm across — its outside diameter is 114.3 mm. The table above is what connects the two systems.
Worked examples
Example 1 — DN100 to NPS
- DN100 is NPS 4.
- Outside diameter:
- In inches: exactly.
A DN100 pipe has a 114.3 mm (4.5 in) outside diameter.
Example 2 — DN50 to NPS
- DN50 is NPS 2.
- Outside diameter:
- In inches:
The nominal NPS 2 outside diameter is in (2.375 in). The 0.001 in gap is rounding — the millimetre figure is rounded to 0.1 mm.
Example 3 — NPS 6 to DN
- NPS 6 is DN150.
- Outside diameter:
- In inches:
For NPS 4 and above, DN is normally 25 times the NPS number (6 × 25 = 150). Below NPS 4 the pairs are fixed by convention, not by multiplication — NPS 2 is DN50, not DN50 by any rule you can compute.
Assumptions and limits
- ASME-series outside diameters. Every OD in the table is the ASME B36.10 series value. EN steel pipe uses a slightly different outside diameter on a few sizes — DN20 is 26.9 mm and DN25 is 33.7 mm in the EN series, against 26.7 mm and 33.4 mm here. Check which series your pipe follows before ordering.
- Nominal sizes are labels, not measurements. DN25 pipe has a 33.4 mm outside diameter, not 25 mm. The DN number is roughly the bore, the NPS number is roughly the bore in inches, and neither equals the outside diameter.
- Range covered. The table covers DN15 to DN300 (NPS 1/2 to NPS 12). For larger sizes, check ISO 6708 or ASME B36.10 directly.
- Outside diameter is schedule-independent. For a given NPS, the outside diameter stays the same whatever the wall thickness (schedule) — a heavier schedule shrinks the bore, never the OD.
- 6 rows still to confirm. The rows for DN32, DN65, DN125, DN200, DN250 and DN300 are marked “to confirm” in the table: they were not yet checked against a second source. The values shown are the best available, but verify them before ordering.
Next step
Matching a DN pipe to an NPS flange? Check whether the two flanges actually bolt together: Flange compatibility checker
FAQ
Are DN and NPS the same thing?
No. DN (Diameter Nominal) is the metric size system from ISO 6708; NPS (Nominal Pipe Size) is the inch-based system from ASME B36.10. The two happen to align row by row — DN100 is NPS 4, DN50 is NPS 2 — but the numbers are not interchangeable: DN100 is not NPS 100, and you cannot convert one to the other by multiplying. Use the table.
Why does the outside diameter matter more than the nominal size?
Because fittings, flanges and couplings mate on the outside diameter, not on the nominal size. Two pipes with the same DN have the same OD whatever their wall thickness, so the OD is the dimension that decides whether a fitting fits. The nominal size is only a label for ordering and referencing.
Why do EN and ASME outside diameters differ on some sizes?
The two systems standardised pipe independently, so a few sizes ended up with different ODs. This table uses the ASME series. In the EN series, DN20 is 26.9 mm (not 26.7 mm) and DN25 is 33.7 mm (not 33.4 mm). On a mixed-standard project, confirm which series the pipe, fittings and flanges all follow.
What does “to confirm” mean on some table rows?
It means that row has not yet been checked against a second source. 8 of the 14 rows were verified against a published conversion table; the other 6 — DN32, DN65, DN125, DN200, DN250 and DN300 — still need that second check. The values shown are the best available, and the converter works for them, but verify them against the standard or a supplier catalogue before ordering.
What if my size is not in the table?
The table covers DN15 to DN300 (NPS 1/2 to NPS 12), the sizes in ISO 6708 and ASME B36.10 up to NPS 12. For larger sizes, look them up in the standard itself: above NPS 14 the outside diameter in inches equals the NPS number, so DN350 is NPS 14 with a 14 in (355.6 mm) OD.
Sources
- Epcland, "DN vs NPS vs PN" conversion table
- Project Materials, "DN to NPS Conversion Chart"
- Standards: ISO 6708 (DN designation), ASME B36.10 (NPS sizes and outside diameters)
For preliminary estimates only. Verify against manufacturer data and the governing standard before purchase or installation.