Flange Compatibility Checker: EN 1092-1 vs ASME B16.5
Check whether an EN 1092-1 flange bolts up to an ASME B16.5 flange. Pick a flange on each side and compare the connection dimensions — bolt circle, bolt holes and sizes — before ordering or cutting pipe.
Side A
Side B
Connection dimensions only. This checker does not compare pressure–temperature ratings or facing types. A “Compatible” verdict does not mean the joint is rated for your service — check the pressure–temperature rating and the facing/gasket separately.
Side A: DN100 PN16 (EN 1092-1) · Side B: NPS 4 Class 150 (ASME B16.5)
| Item | Side A | Side B | Result |
|---|---|---|---|
| Flange outside diameter | 220 mm | 228.6 mm | ✗ mismatch |
| Bolt circle diameter | 180 mm | 190.5 mm | ✗ mismatch |
| Number of bolt holes | 8 | 8 | ✓ match |
| Hole diameter | 18 mm | 19.1 mm | ✗ mismatch |
| Bolt size | M16 | 5/8 in | ✗ mismatch |
Bolt circle diameter and hole count decide whether the flanges bolt up. Outside diameter does not — ASME outside diameters here are inches × 25.4, while metric tables round them (for example NPS 4 Class 150 is 228.6 mm here and 230 mm in some metric tables).
What to do: use a spool piece (conversion spool / adapter) between the two flanges — do not force bolts through misaligned holes.
Next step: Pick the flange material →
Formula
There is no formula here — this is a dimensional comparison, not a calculation. The checker looks up the connection dimensions of each flange and compares the bolt circle diameters:
| Symbol | Meaning | Unit |
|---|---|---|
| ΔK | Bolt-circle difference | mm |
| K | Bolt circle diameter (K) | mm |
| n | Number of bolt holes | — |
Verdict rules, applied to the two flanges:
- Compatible — same hole count and .
- Near match — same hole count and . The bolts may pass, but the two standards do not recognise each other as interchangeable — engineering confirmation is required.
- Not compatible — anything else (different hole count, or ).
These thresholds are the author’s suggested values and may be tuned — they are a practical rule of thumb, not a requirement from either standard.
Worked examples
Example 1 — DN100 PN16 vs NPS 4 Class 150: Not compatible
- Side A: DN100 PN16 (EN 1092-1) — bolt circle , 8 holes.
- Side B: NPS 4 Class 150 (ASME B16.5) — bolt circle , 8 holes.
- Same hole count, but is far over the 2 mm limit, so the verdict is Not compatible. The bolt patterns cannot line up — use a spool piece between the two flanges.
Example 2 — DN150 PN16 vs NPS 6 Class 150: Near match
- Side A: DN150 PN16 (EN 1092-1) — bolt circle , 8 holes.
- Side B: NPS 6 Class 150 (ASME B16.5) — bolt circle , 8 holes.
- Same hole count and sits inside the 0.5–2 mm band, so the verdict is Near match. The bolts may pass through the hole clearance, but the two standards do not recognise each other as interchangeable — get engineering confirmation before relying on the joint.
Assumptions and limits
- Connection dimensions only. This checker compares outside diameter, bolt circle diameter, number of bolt holes, hole diameter and bolt size. It does not compare pressure–temperature ratings or facing types. A “Compatible” verdict does not mean the joint is rated for your service — check the pressure–temperature rating and the facing/gasket separately.
- Scope of the first release. DN15–DN300, EN 1092-1 PN10/16/25/40 and ASME B16.5 Class 150/300 only. Larger sizes and other ratings are not in the tables.
- Verdict thresholds are suggested values. Same hole count and a bolt-circle difference up to 0.5 mm gives Compatible, 0.5–2 mm gives Near match, anything else gives Not compatible. These limits are the author’s suggestion and may be tuned; they are not in either standard.
- DN65 PN10/PN16 hole count. The standard lists 8 holes, but 4-hole flanges are common on the market and sources disagree. The checker shows the 4-or-8-holes note for this size — confirm the actual hole count on the parts before ordering.
- ASME outside diameters are inches × 25.4. Metric tables round them (NPS 4 Class 150 is 228.6 mm here and 230 mm in some metric tables), so judge bolt-up by the bolt circle and hole count, not by the outside diameter.
- Same size, different rating, often identical. PN10 and PN16 have identical connection dimensions from DN15 to DN150, and so do PN25 and PN40 — so a DN80 PN16 against a DN80 PN40 is Compatible. The rating still matters for pressure, which this checker does not compare.
- No thickness, facing or gasket data. Flange thickness, raised-face height and gasket dimensions are not in the tables and are not compared.
Next step
Once the flanges bolt up, pick a material grade that suits the service: Material equivalents
FAQ
Does a “Compatible” verdict mean the joint is pressure-safe?
No. This checker compares connection dimensions only — bolt circle, hole count, hole diameter and bolt size. It does not compare pressure–temperature ratings or facing types. A Compatible pair can still be wrong for your service if the ratings differ or the facings do not match, so check the pressure–temperature rating and the facing/gasket separately.
What do I do when the verdict is Not compatible?
Use a spool piece (conversion spool / adapter) between the two flanges — a short pipe section with an EN flange on one end and an ASME flange on the other. Do not force bolts through misaligned holes or re-drill a flange to make it fit.
Why do PN16 and Class 150 look similar but not bolt up?
They are two different standard families with different bolt patterns. The sizes line up by nominal bore, but the bolt circles do not: DN100 PN16 has a 180 mm bolt circle while NPS 4 Class 150 has 190.5 mm, both with 8 holes — a 10.5 mm difference no bolt can absorb. Close in size is not the same as interchangeable.
What does “Near match” mean in practice?
The hole counts agree and the bolt circles are within 0.5–2 mm, so the bolts may pass through the hole clearance. But the two standards do not recognise each other as interchangeable, and the hole diameters, bolt sizes and pressure ratings still differ. Treat it as a joint that needs engineering confirmation, not as a direct bolt-up.
Why does DN65 PN10/PN16 show a 4-or-8-holes note?
The standard lists 8 holes for DN65 PN10/PN16, but 4-hole flanges are common on the market and published tables disagree. The verdict depends on which one is actually supplied, so count the holes on the parts before ordering.
Sources
- EN 1092-1, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN designated
- ASME B16.5, Pipe Flanges and Flanged Fittings
- EN 1092-1 flange dimensions — wermac.org, Type 11 flange tables (PN10 / PN16 / PN25 / PN40)
- ASME B16.5 flange dimensions — Engineering ToolBox, Flanges and Bolt Dimensions
- Flange dimension data on this site — EN 1092-1 and ASME B16.5 connection dimensions, DN15–DN300 (see the flange data notes)
For preliminary estimates only. Verify against manufacturer data and the governing standard before purchase or installation.