Pressure to Head Calculator
Convert between pressure and pump head. Enter a pressure and the liquid density to get the equivalent head — or enter a head to get the pressure. Useful when a pump datasheet gives head in metres and a gauge reads in bar or psi.
Next step: Use 10.22 m head in the TDH calculator →
Formula
| Symbol | Meaning | Unit |
|---|---|---|
| H | Head | m |
| p | Pressure | Pa |
| ρ | Liquid density | kg/m³ |
| g | Standard gravity, 9.80665 m/s² | m/s² |
The same pressure lifts a denser liquid less high. That is why pump head is quoted in metres of the liquid being pumped, not in bar — head is independent of the liquid, pressure is not.
Worked examples
Example 1 — SI: 1 bar of water
- Pressure:
- Density: (water)
One bar of water pressure is a 10.20 m column of water.
Example 2 — SI: 5 bar of diesel
- Pressure:
- Density: (diesel)
The same 5 bar lifts diesel higher than water, because diesel is lighter.
Example 3 — US: 50 psi of water
- Pressure:
- Density: (SG 1.0)
The quick rule gives 115.5 ft here — 0.1% high, because 2.31 assumes water at about 60 °F. This calculator uses the exact relation, so it matches the density you enter.
Assumptions and limits
- Incompressible liquid only. The relation assumes density does not change with pressure, so it is for liquids, not gases.
- Constant density. If the liquid temperature changes along the column, use the density at the relevant temperature (see the water vapor pressure and density table).
- Standard gravity. The calculator uses . Local gravity varies by less than 0.3% worldwide, which is smaller than the usual gauge error.
- Static pressure. Head from this calculator is the static head of a liquid column. It does not include velocity head or friction loss — those belong in the total dynamic head calculator.
Next step
Got a head value? Add friction and elevation to get the pump's total dynamic head: Total dynamic head (TDH) calculator
FAQ
How many feet of head is 1 psi?
About 2.31 ft of water. The exact number depends on the liquid: 1 psi lifts water about 2.31 ft, diesel about 2.72 ft, because head = pressure / (density × g). The rule of thumb H(ft) = 2.31 × psi / SG works for any liquid if you divide by its specific gravity.
Why does the 2.31 shortcut give a slightly different answer from this calculator?
The shortcut 2.31 assumes water at about 60 °F, with a density near 999 kg/m³. This calculator uses the exact relation H = p / (ρg) with the density you enter, so for water at 20 °C it gives 115.3 ft for 50 psi instead of the shortcut’s 115.5 ft — a 0.1% difference.
Does this work for gases?
No. Gases compress, so their density changes with pressure and a single H = p / (ρg) does not apply. Use this calculator for liquids only.
Should I use gauge or absolute pressure?
Head comes from a pressure difference, so use the same reference on both sides. For a pump, use the pressure rise across the pump (discharge minus suction). If both readings are gauge pressures, the difference is the same as the absolute difference.
Why is pump head quoted in metres instead of bar?
Because head is independent of the liquid: a pump that delivers 50 m of head lifts water 50 m and diesel 50 m, but the discharge pressure is different (about 4.9 bar for water, 4.2 bar for diesel). Quoting head keeps the pump curve valid for any liquid.
Sources
- Hydrostatic head — Wikipedia, "Head (hydraulic)"
- Constants: standard gravity g = 9.80665 m/s², 1 psi = 6894.757 Pa, 1 ft = 0.3048 m
- Water density at temperature — see the water vapor pressure and density table on this site
For preliminary estimates only. Verify against manufacturer data and the governing standard before purchase or installation.